攪拌車在預拌混凝土方面的正常操作
混凝土自上料攪拌車的使用現如今已經在各個施工場地中發展了大作用，當然如果操作人員使用了不正確的操作方法，那施工的質量或者問題就很人擔憂了，下面混凝土自上料攪拌車廠家來講講攪拌車在預拌混凝土方面的正常操作是怎樣的。
The use of self loading concrete mixer has now played a significant role in various construction sites. Of course, if the operators use incorrect operation methods, the construction quality or problems will be very worrying. Next, the manufacturer of the self loading concrete mixer will talk about the normal operation of the mixer in the aspect of ready mixed concrete.
1、預拌混凝土的進料攪拌：在發動機怠速的情況下，將操作手柄撥至“進料攪拌”的“高速”位置；
1. Feeding mixing of ready mixed concrete: when the engine is idling, turn the operating handle to the "high speed" position of "feeding mixing";
a、預拌混凝土的攪動與攪拌車行駛：將操作手柄撥至“攪動”位置；攪拌車行駛前須將駕駛室內的軟軸控制手柄提至鎖定位置；
a. Mixing of ready mixed concrete and driving of mixer truck: turn the operating handle to the "mixing" position; Before the mixer truck runs, the flexible shaft control handle in the cab must be raised to the locked position;
b、解除鎖定：將操作手柄向“進料攪拌”側推到位，如在駕駛室內進行操縱，只要將手柄退出鎖定位置，即可解除鎖定；
b. Unlocking: push the operating handle to the side of "feeding mixing" in place. If the handle is operated in the cab, it can be unlocked as long as the handle is pulled out of the locked position;
c、攪拌筒的停轉：將操作手柄撥至“空擋”。
c. Stop of mixing drum: turn the operating handle to "neutral".
注意：無論是將操作手柄從進料側撥至出料側還是從出料側撥至進料側，皆應使其在空擋位置稍作停留，待筒體停止轉動后方可撥至下一操作位置。
Note: Whether the operating handle is moved from the feeding side to the discharging side or from the discharging side to the feeding side, it should stay in the neutral position for a while, and can be moved to the next operating position after the barrel stops rotating.
進料前應先檢查攪拌筒內是否有水，如有積水，將發動機轉速控制在700-1000rpm，將操縱手柄撥至出料位置，以便排除積水。
Before feeding, check whether there is water in the mixing drum. If there is water, control the engine speed at 700-1000rpm, and turn the operating handle to the discharge position to remove the water.
2、預拌混凝土：
2. Ready mixed concrete:
a、先注入總水量2/3的水；
a. Inject 2/3 of the total water volume first;
b、將1/2的粗骨料，1/2的砂，全部的水泥順次送入攪拌筒，隨后再將余下的1/2粗骨料和水送入；
b. 1/2 of the coarse aggregate, 1/2 of the sand and all the cement are sent into the mixing drum in sequence, and then the remaining 1/2 of the coarse aggregate and water are sent into the mixing drum;
c、攪拌筒轉速及攪拌時間：
c. Rotating speed and mixing time of mixing drum:
進料時攪拌筒的轉速：6—10轉/分；
Rotating speed of mixing drum during feeding: 6-10 rpm;
攪拌時攪拌筒的轉速：6—10轉/分；
Rotating speed of mixing drum during mixing: 6-10 rpm;
攪拌時間：10—16分鐘。
Mixing time: 10-16 minutes.
d、攪拌完畢后的攪動及出料方法與前述相同。
d. The method of stirring and discharging after mixing is the same as the above.
其實，對于有相關設備操作經驗的人來講，攪拌車易上手，即使是毫無經驗的操作人員，廠家也會由專人給出系統培訓，所以如果您有需求就可以來我們網站http://m.bflrsn.cn咨詢了解了。
In fact, for those with relevant equipment operation experience, the mixer is easy to use. Even the inexperienced operators, the manufacturer will also assign special personnel to provide system training, so you can come to our website if you need http://m.bflrsn.cn I understood after consulting.
下一篇：二手自上料攪拌車的購買技巧上一篇：自上料攪拌車的優勢及其操作注意事項
