攪拌車更換液壓油及齒輪油需注意的事宜
攪拌車的保養少不了液壓油及齒輪油的定期更換，這是相當關鍵的，更換過程也需注意，做不好會造成液壓件故障、悶罐現象，接下來自上料攪拌車廠家給大家講講液壓油及齒輪油更換時需注意的事宜吧。
The maintenance of the mixing truck requires regular replacement of hydraulic oil and gear oil, which is quite crucial. Attention should also be paid to the replacement process. Failure to do so can cause hydraulic component failures and tank tightness. Next, let's talk about the matters needing attention when replacing hydraulic oil and gear oil from the manufacturer of the loading mixing truck.
1、加油或換油時，發動機必須處于停止狀態，否則將造成液壓系統損壞。
1. When refueling or changing oil, the engine must be stopped, otherwise damage to the hydraulic system will occur.
2、每次換油前，必須檢查整個系統的密封性能，重新緊固所有的螺栓，必要時更換新的密封元件。
2. Before each oil change, it is necessary to check the sealing performance of the entire system, retighten all bolts, and replace new sealing elements if necessary.
3、禁止不同牌號的液壓油、齒輪油混用或使用不合格油品。車輛出廠時使用的油品型號在油箱上的標簽和《說明書》上都有顯示，初次換油時如果所用油品與出廠時油品型號不同，須清洗液壓系統。
3. It is prohibited to mix hydraulic oil and gear oil of different brands or use unqualified oil products. The type of oil used when the vehicle leaves the factory is shown on the label on the fuel tank and in the Manual. If the oil used during the initial oil change is different from the type of oil used when the vehicle leaves the factory, the hydraulic system must be cleaned.
4、更換出的廢油，應妥善保存和處理，不能隨意倒掉，注意保護環境。
4. The replaced waste oil should be properly stored and disposed of, and should not be arbitrarily dumped. Attention should be paid to protecting the environment.
5、在新換好油品后，讓發動機在攪拌筒不轉的情況下，空轉15分鐘，檢查油位是否合適。
5. After the new oil is replaced, let the engine idle for 15 minutes without the mixing drum running, and check whether the oil level is appropriate.
此外建議大家在保養時一定要選擇原廠純正的油品和濾芯，保證系統運轉正常。齒輪油主要起潤滑，沖洗，防銹等作用，減速機在運轉過程中，會產生金屬磨料，磨料經過沉淀，會被放油堵上的磁鐵吸附，當磨料達到一定量后，會混在油中，加速齒輪和軸承磨損；同時，長期不換油，油液的綜合性能也會降低，影響減速機的使用壽命。
In addition, it is recommended that you choose genuine oil products and filter elements from the original factory during maintenance to ensure the normal operation of the system. Gear oil is mainly used for lubrication, flushing, rust prevention, and other functions. During the operation of the reducer, metal abrasives will be generated. After precipitation, the abrasives will be absorbed by the magnets on the oil drain plug. When the amount of abrasives reaches a certain amount, they will be mixed in the oil, accelerating the wear of the gears and bearings; At the same time, if the oil is not changed for a long time, the comprehensive performance of the oil will also decrease, affecting the service life of the reducer.
攪拌車更換液壓油及齒輪油需注意的事宜就講解到這里了，您對此有怎樣的疑惑或者需求就來我們網站http://m.bflrsn.cn咨詢了解吧！
That's all we need to pay attention to when replacing hydraulic oil and gear oil on the mixer truck. If you have any doubts or needs about this, please come to our website http://m.bflrsn.cn Consult and understand!
