攪拌車的安裝與拆卸過程需注意很多事項！
我們在安裝與拆卸攪拌車的過程中有非常多需要關注的問題，如果大家在平時對這方面只是的了解不多的話，就跟著小編一起來看一看相關內容吧。
We have a lot of problems to pay attention to in the process of installation and disassembly of mixing truck. If you don't know much about this at ordinary times, let's follow the small series to take a look at the relevant content.
混凝土自上料攪拌車軸承的安裝、拆卸方法，應根據軸承的結構、尺寸大小和與軸承部件的配合性質而定。安裝、拆卸的壓力應直接加在緊配合的檔圈端面上，不能通過滾動體傳遞壓力。
The installation and disassembly methods of bearings of concrete self-feeding mixer truck should be determined according to the structure, size and matching nature of bearing components. The pressure of installation and disassembly should be directly added to the end face of the tightly matched gear ring, and the pressure can not be transferred through the rolling body.
因為這樣會在軸承工作表面造成壓痕，影響軸承正常工作，甚至會使軸承損壞。軸承的保持架、密封圈、防塵蓋等零件很容易變形，安裝或拆卸軸承的壓力不能加在這些零件上。
Because this will cause indentation on the working surface of the bearing, affect the normal operation of the bearing, and even make the bearing damaged. Bearing cage, sealing ring, dust cover and other parts are easy to deformation, installation or disassembly bearing pressure can not be added to these parts.
軸承內圈與軸是緊配合，外圈與殼體為較松配合，可用壓力機將軸承先壓裝在軸承上，然后將軸連同軸承一起裝入殼體中，壓裝時在軸承端面上墊一軟金屬材料的裝配套管（銅的或軟鋼管）。裝配套管的內徑應比軸頸直徑略大，外徑應小于軸承內徑的擋邊直徑，以免壓在保持架上。
The inner ring of the bearing is closely matched with the shaft, while the outer ring is loosely matched with the shell. The bearing can be pressed on the bearing first, and then the shaft and the bearing are loaded into the shell together. When pressing, a soft metal assembly sleeve （copper or soft steel pipe） is padded on the end face of the bearing. The inner diameter of the assembly bushing should be slightly larger than the diameter of the journal, and the outer diameter should be smaller than the diameter of the guard edge of the bearing inner diameter, so as not to press on the cage.
混凝土自上料攪拌車廠家認為，軸承內圈與軸，外圈與殼體孔都是緊配合，裝配套管端面應做成能同時壓緊軸承內外套圈端面的圓環，或用一圓盤和裝配套管，使壓力同時傳到內外圈上，把軸承壓入軸上和殼體中。此種安裝方法特別適用于能自動調心的向心球面軸承的安裝。
Concrete mixing truck manufacturers think that bearing inner ring and shaft, outer ring and shell hole are closely matched, assembly sleeve end should be made to be able to press the bearing inner and outer ring end ring at the same time, or with a disc and assembly sleeve, so that the pressure is transmitted to the inner and outer ring at the same time, the bearing pressed into the shaft and shell. This installation method is especially suitable for the installation of self-aligning centripetal spherical bearings.
只要大家按照正確的方法安裝與拆卸攪拌車的話是不用擔心會影響到它的使用的，能夠得到不錯的使用效果。更多內容就來網站m.bflrsn.cn看看相關信息吧。
As long as you install and remove the mixing truck in the correct way, you do not need to worry about affecting its use, and you can get a good use effect. For more information, visit m.bflrsn.cn.
