自動上料攪拌車出現粘灌現象的原因？
在日常使用自動上料攪拌車的時候會發現罐體越來越小了，原因就是沒有清洗好是材料粘在罐壁了，接下來小編想為大家介紹的是自動上料攪拌車出現粘灌現象的原因。
In the daily use of the automatic feeding mixer, we will find that the tank body is getting smaller and smaller. The reason is that the material is stuck on the tank wall. Next, Zhongke Jufeng manufacturer would like to introduce to you the reasons for the phenomenon.
1、回廠檢查罐內水量
1. Return to the factory to check the water volume in the tank
每次出車任務完成回到站內的時候，檢查儲水罐內的水量，讓水罐中的水隨時處于滿罐的狀態，以備不時之需。
When returning to the station after the completion of the task, check the water volume in the water storage tank to make the water in the water tank full at any time in case of emergency.
2、隨車帶上減水劑
2. Bring water reducer with the vehicle
減水劑是一種在維持混凝土坍落度不變的條件下，能減少拌合用水量的混凝土外加劑，隨車攜帶，能對混凝土進行很好的調節。不過在加入減水劑的時候，一定要記得有商砼站化驗室的人在場，否則混凝土質量強度不夠，駕駛員要承擔后果。
Superplasticizer is a kind of concrete admixture which can reduce the mixing water under the condition of maintaining the concrete slump unchanged. It can be carried along with the vehicle and can adjust the concrete well. However, when adding water reducing agent, we must remember that there are people in the laboratory of commercial concrete station, otherwise the concrete quality strength is not enough, and the driver should bear the consequences.
3、減少車輛行駛時間
3. Reduce vehicle travel time
混凝土運距一般在直徑30千米范圍以內，出車之前規劃好路線以及車輛通行情況，盡量減少自動上料攪拌車在路上的時間。
The concrete transportation distance is generally within the range of 30km in diameter. The route and vehicle traffic condition shall be well planned before the vehicle is sent out, so as to minimize the time of the automatic feeding mixer truck on the road.
4、離廠前檢查混凝土質量
4. Check the concrete quality before leaving the factory
可能會因為原料的不同，每一盤混凝土質量都會有變化。在裝好混凝土離場時，一定要檢查罐內混凝土的塌落度情況以及和易度，小心混凝土的提前凝結和混凝土分層沉淀。
Due to the different raw materials, the quality of each plate of concrete will change. When loading and leaving the site, it is necessary to check the slump and workability of the concrete in the tank, and be careful of the early setting of the concrete and the layered precipitation of the concrete.
5、減少損失先卸料
5. Reduce loss and unload first
如果遇到人為因素或者不可抗因素，導致長時間無法卸料的情況，應隨時查看罐內混凝土情況，一旦發現混凝土開始凝結。在報備負責人之后立刻進行卸料，以防整個罐體報廢。
If human factors or irresistible factors lead to long time unable to unload, check the concrete condition in the tank at any time, once the concrete starts to set. Discharge immediately after reporting to the person in charge to prevent the whole tank from being scrapped.
以上就是自動上料攪拌車出現粘灌現象的原因，大家學會之后就能很大程度上避免這個問題，就可以提升自己的工作效率，減少物料損失啦。想要了解更多信息歡迎咨詢官網。
The above is the reason why the automatic feeding mixer appears sticky irrigation phenomenon. After you learn it, you can largely avoid this problem, and you can improve your work efficiency and reduce material loss. For more information, please consult the official website .
下一篇：混凝土攪拌車翻車現象頻發是怎么回事？上一篇：怎樣防止攪拌車剎車失靈？
