攪拌車轉向輪輪胎胎面或兩邊不正常磨損的原因
在自上料攪拌車四輪定位檢測中，經常會遇到駕駛員朋友前來要求解決輪胎磨損的問題。還有的車輛在定位檢測中發現前束數值超差太大，經檢查輪胎已經磨損。下面自上料攪拌車廠家主要來講講攪拌車轉向輪輪胎胎面或兩邊不正常磨損的原因。
In the four wheel positioning detection of self loading mixer, the driver friends often come to solve the problem of tire wear. In other vehicles, the toe in value is found to be too out of tolerance during positioning detection, and the tires have been worn after inspection. The following is mainly about the causes of abnormal wear of the steering wheel tire tread or both sides of the mixer truck from the charging mixer truck manufacturer.
輪胎胎面或兩邊不正常磨損
Abnormal wear of tire tread or both sides
解決方法：檢查胎壓是否過低或輪胎質量是否過關。不要貪圖便宜使用三無輪胎。輪胎的鋼圈是否失圓，做個動平衡。檢查前束尺寸、轉向拉桿球頭是否松曠，方向機固定螺絲有沒有松動。轉向橋主軸或壓力軸承是否磨損嚴重變形或損壞。
Solution: Check whether the tire pressure is too low or the tire quality is up to standard. Don't try to use three no tires cheaply. Check whether the steel rim of the tire is out of round and conduct dynamic balance. Check the toe in size, whether the steering rod ball head is loose, and whether the steering gear fixing screws are loose. Whether the main shaft or pressure bearing of the steering axle is seriously worn, deformed or damaged.
后輪輪胎胎面呈不規則型磨損
The tread of the rear wheel tire is worn irregularly
解決方法：檢查鋼圈，輪轂螺絲及軸頭螺絲是否松動。檢查自上料攪拌車的剎車轂是否失圓。彈簧板和弓卡固定螺絲是否有松動。日常勤檢查輪胎氣壓，要看看輪胎胎面的磨損情況。早發現早修理，把損失降到低限度
Solution: Check whether the steel ring, hub screws and shaft head screws are loose. Check whether the brake hub of the self feeding mixer is out of round. Check whether the fixing screws of spring plate and bow clamp are loose. Check the tire pressure frequently and check the wear of the tire tread. Early detection and early repair to minimize losses
輪胎中間部分的早期磨損
Early wear of the middle part of the tire
解決方法：適當提高輪胎充氣量，可以減小輪胎與路面的接觸面積，從而減小輪胎的滾動阻力，節約燃油。但充氣量過大時，不但影響輪胎的減振性能，還會使輪胎變形量過大，與地面的接觸面積太小，磨損只能由胎面部分承擔，形成早期磨損。
Solution: Properly increasing the tire inflation can reduce the contact area between the tire and the road, thus reducing the rolling resistance of the tire and saving fuel. However, when the inflation volume is too large, it will not only affect the damping performance of the tire, but also make the tire deform too much, the contact area with the ground is too small, and the wear can only be borne by the tread, forming early wear.
定期檢查全自動攪拌車輪胎氣壓以及胎面花紋，另外每行駛8000-10000公里對全自動攪拌車輪胎進行前后或交叉調位(視具體車型而定)等，都可以很好的保護好全自動攪拌車輪胎。更多相關內容就來我們網站http://m.bflrsn.cn進行咨詢吧！
Regularly check the tire pressure and tread pattern of the fully automatic mixer. In addition, every 8000-10000 km, adjust the tires of the fully automatic mixer forward and backward or cross (depending on the specific model), which can protect the tires of the fully automatic mixer well. More relevant content will come to our website http://m.bflrsn.cn Consult!
