怎樣緊急處理攪拌車發生的故障？
上次遇到一個問題，有個裝載混凝土的攪拌車發生了故障，必須要緊急處理才行，下面給大家說說我們是怎樣緊急處理的：
Last time I encountered a problem. A mixer truck loaded with concrete broke down and had to be dealt with urgently. Here's how we deal with it urgently:
1、裝載混凝土時如攪拌車發生故障時，拌筒不能旋轉，應迅速將拌筒內的混凝土排出，那么怎樣排出混凝土呢？
1. When loading concrete, if the mixer fails and the mixing drum cannot rotate, the concrete in the mixing drum should be discharged quickly. How to discharge the concrete?
判斷是發動機或柱塞泵發生故障還是馬達或減速器發生故障。
First, judge whether the engine or plunger pump fails or the motor or reducer fails.
如是發動機或柱塞泵發生故障，馬達或減速器能正常使用，請按以下方法處理：
If the plunger or motor fails, please handle it according to the following methods:
連接緊急驅動軟管（兩車泵、馬達相同），依靠其它攪拌車的動力，驅動拌筒旋轉并將混凝土排出。
Connect the emergency drive hose (the pumps and motors of the two trucks are the same), drive the mixing drum to rotate and discharge the concrete by relying on the power of other mixing trucks.
怎樣緊急處理攪拌車故障_諸葛修車網
How to deal with the failure of mixer truck urgently_ Zhuge car repair network
2、具體操作步驟如下：
2. The specific operation steps are as follows:
⑴ 準備工作
(1) preparation
準備好三根緊急驅動軟管，卸下接管和接頭蓋。
Prepare three emergency drive hoses and remove the connecting pipe and connector cover.
⑵ 故障車（被驅動車）的操作
(2) operation of faulty vehicle (driven vehicle)
將故障車的發動機熄火；
Turn off the engine of the faulty vehicle;
將緊固螺母（左右各有一個）朝左旋松；
Loosen the fastening nut (one on the left and one on the right) to the left;
再將旋鈕朝右旋轉，直到不能再旋為止；
Turn the knob to the right until it can no longer be rotated;
將高壓軟管從馬達接頭處卸下；
Remove the high-pressure hose from the motor connector;
將緊急驅動軟管接到馬達接頭上；
Connect the emergency drive hose to the motor connector;
把緊急驅動軟管上的接管與故障車卸下的高壓軟管相接，以防漏油。
Connect the connecting pipe on the emergency drive hose with the high-pressure hose removed by the faulty vehicle to prevent oil leakage.
⑶ 救援車（驅動車）的操作
(3) operation of rescue vehicle (drive vehicle)
將操作手柄于空檔位置；
Set the operating handle to the neutral position;
將發動機熄火；
Turn off the engine;
將高壓軟管從高壓油管處卸下；
Remove the high-pressure hose from the high-pressure oil pipe;
將緊急驅動軟管接到高壓油管上；
Connect the emergency drive hose to the high-pressure oil pipe;
用緊急驅動軟管上的接頭蓋將驅動車的高壓軟管蓋起，以防漏油。
Cover the high-pressure hose of the drive vehicle with the connector cover on the emergency drive hose to prevent oil leakage.
⑷ 啟動救援車的發動機。
(4) start the engine of the rescue vehicle.
⑸ 將救援車的操作手柄撥“出料”位置，使故障車內的混凝土排出。
(5) turn the operating handle of the rescue vehicle to the "discharge" position to discharge the concrete in the faulty vehicle.
⑹ 緊急驅動完畢后，使兩車各自恢復原狀。
(6) after the emergency drive is completed, restore the two vehicles to their original state.
